RUVIMAT SP 12 is a three layer polymeric membrane based on high quality plastisized PVC with inner polyester reinforcement scrim.
Application: A membrane for lining waterproofing of swimming pools or other hydrotechnical equipments.
Size: 40m² Width: 2m
Package: Roll Length: 20m
RUVIMAT SP 12 is a three layer polymeric membrane based on high quality plastisized PVC with inner polyester reinforcement scrim. Application: A membrane for lining waterproofing of swimming pools or other hydrotechnical equipments. RUVIMAT SP 12 is produced in compliance with EN 13956 : 2012 . Rolled sheet membrane, reinforced Each roll is packed in a transparent polyethylene film Rolls must be stored in horizontal direction on the pallets in the original packing without direct exposure to sunlight, rain and snow. Storage following these rules guarantees no expiry date. Do not double stack the pallets during transport and storage. treatment (Dimensional Stability)
The surface of the base and walls of the pool must be firm, smooth , without sharp protrusions , clean and dry , free of oils , paint , dust etc. Before the laying of the membrane should be placed a layer of geotextile . Temperature Compatibility: It is not allowable direct contact with the polymers of other groups, such as polystyrene, polyurethane, polyisocyanate, phenol containing foam. The membrane is not resistant to bituminous materials , grease, tar , oils , solvents . If it is in contact with such surfaces , has to be used a separation layer of geotextile with a density of min.300g / m² , in order to be preventable the accelerated aging. Technology of the installation / Tools Technology of the installation: Technology of the installation : In compliance with the existing Installation manual for roofing membrane Ruvimat. Method of attachment: Free installation with a mechanical fixing. The sheets of the waterproofing membrane are free layed and mechanically fastened to the base by the end of the coil in the area of sheets overlapping , or outside this area. It is imperative that the additional mechanical fixing of the membrane around the perimeter of the swimming pool. Estimate for the quantity of linings is performed by the technical department of the company providing the installation Technology of the welding : The overlaps ( from 80 to 100 mm) of the membrane must be welded by electric tools with hot air, hand held heat gun and roller or welding automatic tools with hot air, that have indiviul setting and control of welding temperature with a capacity of minimum +600°С. Recommended mode for the equipment : Welding parameters – The parameters of the welding process include temperature, welding speed, air stream, pressure must be chosen and checked according the weather conditions and the type of welding tools on the building area right before the welding process starts. The width of the joint must be at least 30 mm. The quality control is done with a screwdriver after the joint is cooled. All the unwelded points must be repaired with the welding tools. After completing the membrane installation must be tested the watertightness of the system. Application limits The application of PVC membrane RUVIMAT SP 12 must be performed by people that have passed a training course. Temperature of the deck : minimum -20°C / maximum +50°C. Temperature of the environment : minimum -15°C / maximum +50°C. The application of chemical components, such as contact adhesives / cleaner for membranes of PVC is possible at temperature not lower than +5 ° C. Please contact for technical information on these products before use. RUVIMAT SP 12 is an article within the meaning of Regulation (EC) 1907/2006 Article 3.3. A Material Safety Data Sheet following EC- Regulation 1907/2006, Article 31 is not required for the product when sold, shipped or used. The product has no harmful effects on environment and human health when is stored and used as specified. Regulation of the EU on chemicals and their safe use ЕО 1907/2006 /REACH/ RUVIMAT SP 12 is an article within the meaning of Regulation (EC) No 1907/2006.The product does not contain any substances intended to be released from it under normal conditions of storage, use and service. Therefore, there are no registration requirements for substances in the article within the meaning of Article 7(1) of the Regulation. Safety: Ventilation and fresh air intake must be ensured when welding of article is performed in closed rooms. Local safety precautions must be observed! Class of Transportation: RUVIMAT SP12 is not classified as hazardous for transportation. Disposal of Residual Waste: Residual waste generated from the use of the product as well as from the roll packaging is recyclable. Disposal must be according to regional and national regulations and EU legislation.
Characteristics – advantages
Indicators / Standards
Клас F acc. European classification for reaction to fire EN 13501-1.Appearance/Colour
Surface: matt
Color:
Packing
Roll length: 20 m
Roll width: 2 m
Roll weight: 60,00 кg
Rolls on the pallet: 24 rollsStoring
Standart
EN 13956:2012
Visible defects
Not present
EN 1850-2
Length
20,00 (-0 % / +5 %)m
EN 1848-2
Width
2,00 (-0,5% / +1%)m
EN 1848-2
Straigthness
≤30 mm
EN 1848-2
Flatness
≤10 mm
EN 1848-2
Thickness
1,2 (-5%/+10 %)mm
EN 1849-2
Mass per unit area
1,5 (-5%/+10 %)кg/m²
EN 1849-2
Tensile strength
Method B
EN 12311-2
warp
≥800 N/50mm
weft
≥800 N/50mm
Elongation
Method B
EN 12311-2
warp
≥15%
weft
≥15%
Tearing strength
EN 12310-2
warp
≥180N
weft
≥180N
Joint peel resistance
≥180N/50mm
EN 12316-2
Resistance to artificial aging
complies
EN 1296
Resistance to UV radiation
complies
EN 1297
Changing the sizes after thermal
EN 1107-2
warp
±1%
weft
±1%
Foldability at low temperature
/ without cracking /up to -30°C
EN 495-5
Base preparation
Application Limits
RUVIMAT SP 12 can be applied on territories where temperature of the environment is not less than – 40 °C , and the constant temperature should be not higher than +50 °C.
Temperature limits
HEALTH AND SAFETY INFORMATION
Call Now
