RUVIMAT BA 18 type Т is a one-layer , not-reinforced polymeric membrane based on high quality plastisized PVC
Application
Waterproofing of groundwater when laying the foundations of buildings , for tunnels and other underground facilities. Prevent the passage of water under hydrostatic pressure from the soil to the interior of the building.
Size: 40m² Width: 2m
Package: Roll Length: 20m
RUVIMAT BA 18 is a one- layer , not – reinforced polymeric membrane based on high quality plastisized PVC Application RUVIMAT BA 18 is produced in compliance with EN 13967: 2012 for moisture insulation of buildings , including underground parts of buildings. Class F acc. European classification for reaction to fire EN 13501-1. Rolled sheet membrane , homogeneous Surface: smooth , matt Color – black – for waterproofing of basements – signal – for waterproofing of tunnels Membrane with a signal color is produced on request at a minimum order quantity of 4000 m² Each roll is packed in clear LDPE film Rolls must be stored in horizontal direction on the pallets in the original packing without direct exposure to sunlight, rain and snow. Storage following these rules guarantees no expiry date. treatment /80˚С, 6h/
Concrete or old facings : The surface of the base must be firm , smooth , without sharp protrusions, clean and dry, free of oils , paint, dust etc . Soil : The earthwork should be tight and the available stones and sharp objects to be removed from the surface. Before the membranes application is placed a subject layer of geotextile . Temperature Temperature of the foundation : minimum 0 C / maximum +35 ° C Temperature of the air : minimum +5 ° C / maximum +35 ° C Compatibility It is not allowable direct contact with the polymers of other groups, such as polystyrene, polyurethane, polyisocyanate, phenol containing foam. The membrane is not resistant to bituminous materials , grease, tar , oils , solvents . If it is in contact with such surfaces , has to be used a separation layer of geotextile with a density of min.300g / m² , in order to be preventable the accelerated aging. Technology of the installation : In compliance with the existing Installation manual for roofing membrane Ruvimat Method of attachment : Free laying with a mechanical fixing or free laying with ballast Technology of the welding : The overlaps ( from 80 to 100 mm) of the membrane must be welded by electric tools with hot air, hand held heat gun and roller or welding automatic tools with hot air, that have indiviul setting and control of welding temperature with a capacity of minimum +600°С. The welds are carried out with a double welding seam providing a chamber for testing the weld. Recommended mode for the equipment : Application limits The membrane is not UV stabilized and should not be applied to open areas under the influence of sunlight. HEALTH AND SAFETY INFORMATION REACH RUVIMAT ВА 18 is an article within the meaning of Regulation (EC) No 1907/2006.The product does not contain any substances intended to be released from it under normal conditions of storage, use and service. Therefore, there are no registration requirements for substances in the article within the meaning of Article 7(1) of the Regulation. Safety Local safety precautions must be observed ! Class of Transportation Disposal of Residual Waste
Waterproofing of groundwater when laying the foundations of buildings , for tunnels and other underground facilities. Prevent the passage of water under hydrostatic pressure from the soil to the interior of the building.Characteristics – advantages
Indicators / Standards
Appearance/Color
Packing
Roll length: 20 m
Roll width: 2 mStoring
Visible defects
Not present
EN 1850-2
Length
20,00 (-0 % / +5 %)m
EN 1848-2
Width
2,00 (-0,5% / +1%)m
EN 1848-2
Straigthness
≤30 mm
EN 1848-2
Flatness
≤10 mm
EN 1848-2
Thickness
1,8 (-5%/+10 %)mm
EN 1849-2
Mass per unit area
2,5 (-5%/+10 %)кg/m²
EN 1849-2
Tensile strength
Method A
EN 12311-2
warp
≥14 N/mm²
weft
≥14 N/mm²
Elongation
EN 12311-2
warp
≥240%
weft
≥240%
Tearing strength
EN 12310-2
warp
≥120N
weft
≥120N
Joint peel resistance
≥200N/50mm
EN 12316-2
Resistance to impact
≥ 700 mm
EN 12691
Resistance to static load /drilling/
≥ 20 кg
EN 12730
Changing the sizes after thermal
EN 1107-2
warp
± 5,0 %
weft
± 2,0 %
Foldability at low temperature
/ without cracking /up to -30°C
EN 495-5
APPLICATION LIMITS
Installation Instructions
Welding parameters – The parameters of the welding process include temperature, welding speed, air stream, pressure must be chosen and checked according the weather conditions and the type of welding tools on the building area right before the welding process starts. The width of the joint must be at least 30 mm. Quality control of the welding joint is carried out by applying a pressure in the chamber between the welding joints .
The application of PVC membrane RUVIMAT BA 18 must be performed by people that have passed a training course .
RUVIMAT ВА18 is an article within the meaning of Regulation (EC) 1907/2006 Article 3.3. A Material Safety Data Sheet following EC- Regulation 1907/2006, Article 31 is not required for the product when sold, shipped or used. The product has no harmful effects on environment and human health when stored and used as specified.
Regulation of the EU on chemicals and their safe use ЕО 1907/2006 /REACH/
Ventilation and fresh air intake must be ensured when welding of article is performed in closed rooms.
RUVIMAT ВА18 is not classified as hazardous for transportation.
Residual waste generated from the use of the product as well as from the roll packaging is recyclable. Disposal must be according to regional and national regulations and EU legislation.
Call Now
